Top 10 Follower Pump Mistakes

If your follower pump is leaking, it’s likely the problem is with the cam follower. This can be caused by a number of things including over-tightening, under-tightening or improper installation. Alternatively, the pump may have been galled by high temperatures or the camshaft lobes may have been damaged by a collision.
1. Over-tightening

Over-tightening a screw can be dangerous because it can weaken the fastener and cause it to break. This is especially true when the fastener is holding a gasket or clamp.

Over-tightening screws can also deform the connection between tube fittings or valves, which makes them less secure and prevents them from doing their job properly.

This could allow fluids to leak out, leading to a host of problems. Besides potentially causing damage to equipment, it can also lead to contamination from dirt or chemicals that may be leaking through the gap between the tubes.

Over-tightening also makes it harder for the tube fittings to reshape themselves, which means that they won’t be able to fit into new applications without being replaced. This will make it more expensive to operate a system and can result in the faster breakdown of the tubes themselves.
3. Improper Installation

Regardless of the type of pump, improper installation can cause problems. The wrong screw selection or improper screw hole column design can lead to a complete production line meltdown. Injection molding can be a complex process, and the proper selection of screws is essential for maximizing productivity.

Another common mistake is the improper use of an impact wrench. This tool was designed to drive large wheel nuts, and it’s not a good idea to use it to drive small screws. The ‘impact’ of the impact wrench can damage the fastener, resulting in poor performance or even fracture. Using a torque wrench instead of an impact tool can prevent this problem and save money. It’s never too late to avoid these mistakes! Keep these tips in mind to help you prevent a meltdown. Stay tuned for more posts like this one!
4. Improper Maintenance

One of the most common screw mishaps is improper maintenance. Many screws are made of a low-quality metal that weakens over time and is susceptible to stripping when subjected to prolonged exposure. It’s best to avoid using any screw that’s been stripped, over-tightened, or sheared because it’s likely the screw will break or fail in an untimely manner.

Another common screw failure is the use of a worn driver bit. The bit can slip out of place and continue to spin, stripping the head of the screw. This is why it’s a good idea to keep several different sizes and shapes of bits on hand. Having them at the ready can save you from having to replace the bit when it’s already worn out. A new bit will sit snugly in the head of the screw, making it less likely to skimp and cause stripping.
5. Faulty Equipment

Faulty equipment is a major cause of workplace injuries. Whether it’s a conveyor belt that stops in the middle of transporting products or a crane that collapses when you’re working on it, faulty equipment is dangerous and can result in serious injury.

Defective equipment also reflects poorly on your business. It can slow down production and damage your bottom line in the long run.

If you’re a victim of faulty equipment, it’s important to figure out where the liability lies. It’s not always easy to pinpoint who is at fault, but determining if the equipment broke down due to general wear and tear or a factory-borne defect can help determine who to hold liable.
6. Faulty Installation

There are a number of reasons that a screw could be set wrong. Whether it was a sloppy installer or a bad design, it can be difficult to spot the fault.

Nevertheless, ปั้มไลค์ is important to ensure that the screws are installed correctly to avoid the common problem of overheating the pump shaft or camshaft. A slight difference in screw depth is enough to cause a pop in the long run.

The most important part of a proper installation is to make sure that the bolts are not tightened all the way, but are instead loosely driven until they are evenly tightened against the engine. This will ensure that the shaft is not overheated and prevents bearing damage from over-tightening. It also helps to lubricate the bearings before installation. The right lubricant can reduce friction and prolong the life of the bearings.
7. Faulty Maintenance

A pump is a critical component in any piping system. Failure of this essential element can lead to serious damage and a high level of downtime.

It is important that pumps are properly maintained to extend their lifespan, increase safety standards and reduce costs. This can be achieved by following manufacturer recommendations and establishing a robust maintenance strategy.

It is also imperative that pump manuals are reviewed and referred to when problems arise. Unfortunately, few people do this. These manuals contain vital information on suitable pump operating conditions, best maintenance practices and alternative replacement parts. They can save companies a lot of time and money. Moreover, these manuals can cut down on the amount of errors made during pump operations and maintenance. The key to success is knowing how to read and apply these manuals. This will ensure your pumps operate as intended and last longer.
8. Faulty Installation

A screw that is set too far out or too deep cannot be hidden by drywall compound or tape. It is a sure sign of a faulty installation.

A similar problem occurs when the screw is not firmly secured to the material, especially on the walls where insulation pushes against it. A slight difference in the depth of a screw can make all the difference between a panel that is tight to the framing and one that is loose.

Fortunately, these errors can be fixed with the right tools and techniques. However, it is important to remember that a little mistake can add up to big problems down the road. To avoid this, always use the best possible tool for the job and do it properly! It is also a good idea to have a few extra pairs of hand tools on hand at all times.
9. Faulty Maintenance

The best way to avoid this problem is to perform a quick and thorough inspection of your follower pumps on a regular basis. By inspecting for cracks or broken seals, you can prevent major damage to the equipment and help to avoid expensive repairs down the road.

In addition, performing a good cleaning of your pump and re-lubricating it regularly is also important. This can reduce wear and tear on the bearings by removing dirt and debris, and by preventing contamination from reaching the ball screw.

Faulty maintenance of any kind can be a costly mistake for any business. If a client or customer suffers a serious injury due to faulty equipment or poor maintenance, the company or individual that caused the problem could be held liable for damages. The cheapest and easiest way to avoid this type of a situation is to perform regular maintenance of your equipment.
10. Faulty Installation

One of the most difficult mistakes to identify is faulty installation. A screw that is set too far out is easy to spot, but a slightly deeper screw is more difficult to see unless a bump has formed.

A screw that is set too far in can be hard to get out, especially if the screw is made of a soft metal. It may be best to try tapping the screwdriver into the metal with a hammer until the screwdriver is in a position that you can twist it out.

If you are unable to unscrew a screw, it might be because the original screw was not suited for the application. Consider purchasing a screw that better meets your application needs and avoid future problems.